Taking some time off for my hobby by building a Comical Hornet on the -02CB chassis.

Still pondering about the paint job, since I‘m pretty certain not to go with box-art.

First step is to take apart the preassembled gearbox to replace the plastic bushings with proper ballbearings. Whoever thought a prebuilt gearbox was a good idea, it is not! This is a kit after all, even a beginner friendly one.

Let the screwing around commence!

Taking apart the gearbox of the just takes a moment. These gears almost *look* bone dry, but they‘re actually somewhat greased.

The differential seems properly greased to me, nothing to do here. I‘ll add some more to the gears.

The white plastic and bronze metal bushings are all the same size throughout the kit. They‘re getting replaced with ball bearings which run smoother, and last longer. It‘s a key upgrade to make in my opinion to enjoying your vehicle for many years to come.

Show thread

As usual with kits, we‘re starting off with the A-Bag from the metal parts.

It contains the iconic Tamiya wrench, which is really super handy. A bunch of different tapping screws, screw-pins, outdrives, cups and dogbones and spacers. We‘ve already used the grease to prep up the gearbox.

The plastic parts come on sprues (or parts trees) which are labelled with a letter for the sprue and a number for the part. Each referenced in the manual.

Show thread

We continue with assembling the rear lower wishbones. The ball connectors will be the mounts for the shocks later on. The different mounting positions allow for vehicle setup like ride height and its tendency to wheelie.

The small O-rings in the drive cups help with sealing the gearbox and put a tiny bit of pressure on the dogbones that go in there to reduce slop.

Show thread

Opening up the b-tree we find rear uprights, front c-hubs, servo horns and saver parts, wheel hexes and some more bits‘n‘pieces.
The designator tells us this is black polycarbonate, a strong and impact resistant with a shiny surface finish.

I‘m replacing the dogbones and wheel axles with universal joints. The are a hop-up option party from a third party manufacturer named Yeah-Racing. This tuning part is probably not really necessary, but I prefer running universal joints.

We‘re opening the two-piece sprue F which contains a few chunky parts. The main chassis frame, a huge and a ginormous front bumper, shock preloading clips, and a wheelie bar.

It‘s made from black Polyamide (Nylon) again which makes sense. These are chunky parts, and the ones taking a lot of the impact energy during crashes and the occasional unfortunate landing after a jump.

The wheelie bar is mounted with spacers to the rear of the gearbox.

Show thread

This concludes build group A if the Comical Hornet buildup kit.

There‘s a few left over parts from the metal bag A. A fee screws which can be used as spares. Sometimes you lose one. The bushings haven‘t been used because we immediately affixed ball bearings in the rear uprights.

The tiny allen key is used for mounting the pinion to the motor shaft which came already premounted. Should you want or need to change it, that‘s the tool you need.

We‘ll continue using the cross-wrench.

Show thread

For build group B we‘ll be needing metal parts bag B to complete steps 5 through 11 in the manual. I‘m sure you already sense a pattern here.

We‘ll need our electronics, to center the steering servo and then build the front suspension and main chassis.

This includes a cameo appearance of the transmitter.

Show thread

To connect the tie-rods to the servo we need a few parts. One piece that directly goes on the servo axle matching the correct number of splines. The C-shaped servo-saver clamp, and the servo horn that connects to the tie-rods via ball joints and cups.

The correct length of the tie rods is stated in the manual and also how exactly it is measured. It helps having calipers available, but if you don‘t you can just align your piece with the 1:1 print in the manual. This applies to screws as well.

Show thread

Getting out the D-tree now, which is made from ABS. A common choice for chassis frames, like this one. The connections between part and tree are somewhat larger and rounded this time, so make sure to remove any burrs.

Mounting the servo takes just two screws and don‘t overlook the washer, like I just did. The rest is just screwing together the chassis sandwich and the receptacle for the front bumper.

Show thread

Getting out the M-tree now with front and rear bumper parts made of black, flexible Nylon. Also the front double wishbones, knuckles and C-hubs. A few bearings, screws, ball joints, screw pins, and even body clips.

It all goes onto the front of the main chassis.

Show thread

The front suspension fully mounted and the tie-rods are connected to the steering servo already. Wishbones are moving freely up and down and drop through gravity alone when lifted up. That‘s how an unloaded suspension should behave.

This part of the assembly is mostly done now.

Concluding group B leaves us with the screws we didn‘t need for our particular servo we used, so that‘s perfectly fine. The remaining screw pins, ball joint and screw are spares.

The 2 bearings are for the rear axle.

Show thread

Build group C, steps 12 through 15, may come as a shock to you because that what it‘s all about.
Building for shock absorbers.

The V- and W- trees made from Nylon will compose the inner shock bodies that hold the damper oil.

To keep this entry friendly kit easy to build, the damping rate of these is not adjustable. That also means, you can’t go wrong and mess up your suspension. :-)

Expect this to be partially messy, so have a few kitchen paper towels ready and a pair of pliers.

Show thread

We‘re building two pairs of shocks, one each for the front and the rear suspension. They‘re *almost* identical. The rear ones sport an additional spacer that limits their travel. Don‘t forget to put that on the piston rod before screwing on the end ball cup.

The ball cups come pre-threaded and go on easily and alined. Make sure the piston is screwed in all the way. The last part needs more force and you must hold on to the piston rod with protective cloth and pliers.
Then slowly fill with oil.

Show thread

As soon as all the bubbles have left the cylinders we can progress with closing them up with the seals and the top cap.
The process is put the green sealing caps on from the side so excess oil can spill over. You just wipe it off carefully with a paper towel.

Screw on the top cap, rinse and repeat four times.

Show thread

Only a few things left to do for build group C. Putting the spring preloading clips onto the shock cylinders, add the coiled springs and snap them into the bottom caps.

You may now clip the shocks onto the balljoints reserved at the front and rear axles. Should almost just snap in place by hand but feel free to use pliers.
Take care to put the ones with the travel limiting spacer on the rear axle and the remaining ones at the front.

You‘re left with O-rings and some sprues. This concludes C.

Show thread

In build group D, we‘re finishing the chassis.

There‘s a good amount of slightly different screws, screwpins, washers and other parts involved in these steps. Nothing that could scare you though. I like sorting the different bits‘n‘pieces on my parts trays to get a better overview and so I can more easily find what I need.

We‘ll unify the front and rear and mount body posts and even some LEDs.

Show thread

Front body post are mounted adjacent to the steering servo. The rear posts sit over the shocks with the taillights on either side.
Suddenly the hornet starts looking like a hedgehog. And it glows furiously red.

Show thread

Step 19 is where the side nerv guards are attached and the power switch. This step uses five (5) different types of screws and four of them are black and only distinguishable by length.
Getting the necessary screws sorted before starting this step and maybe mark them with a quick sticky note will make it easier.

If you accidentally mix up the left and right side, don‘t worry. You can take it apart again and flip a piece around. Just happened to me despite being in the hobby for decades.

Show thread

The funny looking dual antennae are a little fiddly to mount. Turning the vehicle on the side makes matters easier.

The manual also wants us to mount the speed controller and receiver to the top of the chassis using double sided tape.

I‘m using the kit stock ESC because it‘s a versatile piece of electronics and it‘s included. My receiver is quite different in shape and size than the one depicted in the manual though. So I‘ll happily divert from the guide and decide how to affix them later.

Show thread

Of corse need wheels. So we‘ll build multipart rims and mount tires on them.

The rims are two pieces each, not a beadlock construction though. They‘re more of a white tube with a decorative hub cap design where the orange hub cap also is the axle fitting.
Five screws each.

Then you just squeeze the rubbers on. The ballony rimmed front ones are omnidirectional. So nothing special here.

The rear wheels have a directional tread pattern to make a matching pair for left and right wheels.

Show thread

@MacLemon neat! I never realized that the links were 1:1 scale in the manual

Sign in to participate in the conversation

chaos.social – a Fediverse instance for & by the Chaos community